新闻动态
【模具知识】模具设计专业术语详解
1．模胚：A.香港龙记标准模胚，材质为黄牌钢（S50C）；
1. mold: A. Hongkong Longji standard embryo, material is yellow card steel (S50C);
B. 应客人要求可选择其它品牌供货商及订做特殊材料模胚。
B. customers can choose other brands suppliers and customize their special materials.
2．开模坑：模具在顶针板之间制作开模坑，方便维修时装拆模具（应离螺丝位有3.0mm距离）。
2. Opening pit: The mold is made between the thimble plate to facilitate the maintenance of fashion demolition mold (should be 3.0 mm away from the screw position).
3．斜方导滑块：在B板底加斜方导滑块，能保证斜方顶出及复回时动作平稳、顺畅并保证耐摩擦
3. Oblique guide slider: add oblique guide slider at the bottom of B board to ensure smooth and smooth movement of oblique ejection and recovery and ensure friction resistance
4． 斜方：采用P20、H13或预硬H13(DH2F)制作，表面经氮硬处理，增加表面的耐磨性，使其不易擦烧、拉伤、芯部有韧性不易折断、变形、提高模具的使用寿命。
4. Slope: P20, H13 or pre-hardened H13 (DH2F) are used to make the surface hardened by nitrogen to increase the wear resistance of the surface, so that it is not easy to scrape, pull, core toughness is not easy to break, deformation, and improve the life of the mold.
5． 斜方座：采用P20氮硬制作，使斜方底部的滑动面加大，降低斜方底部的磨损率，提高斜方的定位精确度，降低斜方底部磨擦阻力，增加斜方顶出的平稳性，延长斜方使用寿命。
5. Slope base: P20 nitrogen hard manufacturing, so that the slope bottom sliding surface increased, reduce the wear rate of the slope bottom, improve the positioning accuracy of the slope, reduce the friction resistance of the slope bottom, increase the stability of the slope ejection, prolong the service life of the slope.
6．在面针板上加两个顶出限位块，特别是防止斜方座碰撞B板，而损坏斜方。
6. Add two ejection blocks to the needle board, especially to prevent the bevel seat from colliding with the B board and damaging the bevel.
7．中托边司：凡大于3030以上的模具均需加4套中托边司，小于3030以下的模具加2套中托边司，防止顶出系统不顺畅，从而延长模具的使用寿命。
7.Mid-trimmer: Any mold greater than 3030 must be added 4 sets of mid-trimmer, molds less than 3030 plus 2 sets of mid-trimmer, to prevent the ejection system is not smooth, thus extending the life of the mold.
8．模具牌：模具厂标准模具牌，安装在啤塑时操作员一侧，方便识别模具。
8. mold card: mold factory standard mold plate, installed on the operator side of beer plastic, easy to identify the mold.
9．散气镶件：制品易困气部位，通常加散气镶件，但可根据特殊情况增加散气针或散气钢做的镶件，利于排气，从而提高生产效率。（使用日本PorceraxⅡ PM-35钢）
9. Dispersion insert: The product is easy to trap gas parts, usually with a diffuse insert, but according to special circumstances can be added to the diffuse needle or steel insert, conducive to exhaust gas, thereby improving production efficiency. (using Japanese Porcerax II PM-35 steel)
10．锁模片：为保证吊模及运输时的安全，需在啤塑操作员一侧加锁模片。两板模装在A、B板上，三板模安装到面板上与B板上。
10. locking die: to ensure the safety of the lifting and transportation, the mould locking piece is needed on the side of the beer molding operator. The two die is mounted on the A and B boards, and the three plate die is installed on the panel and on the B board.
1. mold: A. Hongkong Longji standard embryo, material is yellow card steel (S50C);
B. 应客人要求可选择其它品牌供货商及订做特殊材料模胚。
B. customers can choose other brands suppliers and customize their special materials.
2．开模坑：模具在顶针板之间制作开模坑，方便维修时装拆模具（应离螺丝位有3.0mm距离）。
2. Opening pit: The mold is made between the thimble plate to facilitate the maintenance of fashion demolition mold (should be 3.0 mm away from the screw position).
3．斜方导滑块：在B板底加斜方导滑块，能保证斜方顶出及复回时动作平稳、顺畅并保证耐摩擦
3. Oblique guide slider: add oblique guide slider at the bottom of B board to ensure smooth and smooth movement of oblique ejection and recovery and ensure friction resistance
4． 斜方：采用P20、H13或预硬H13(DH2F)制作，表面经氮硬处理，增加表面的耐磨性，使其不易擦烧、拉伤、芯部有韧性不易折断、变形、提高模具的使用寿命。
4. Slope: P20, H13 or pre-hardened H13 (DH2F) are used to make the surface hardened by nitrogen to increase the wear resistance of the surface, so that it is not easy to scrape, pull, core toughness is not easy to break, deformation, and improve the life of the mold.
5． 斜方座：采用P20氮硬制作，使斜方底部的滑动面加大，降低斜方底部的磨损率，提高斜方的定位精确度，降低斜方底部磨擦阻力，增加斜方顶出的平稳性，延长斜方使用寿命。
5. Slope base: P20 nitrogen hard manufacturing, so that the slope bottom sliding surface increased, reduce the wear rate of the slope bottom, improve the positioning accuracy of the slope, reduce the friction resistance of the slope bottom, increase the stability of the slope ejection, prolong the service life of the slope.
6．在面针板上加两个顶出限位块，特别是防止斜方座碰撞B板，而损坏斜方。
6. Add two ejection blocks to the needle board, especially to prevent the bevel seat from colliding with the B board and damaging the bevel.
7．中托边司：凡大于3030以上的模具均需加4套中托边司，小于3030以下的模具加2套中托边司，防止顶出系统不顺畅，从而延长模具的使用寿命。
7.Mid-trimmer: Any mold greater than 3030 must be added 4 sets of mid-trimmer, molds less than 3030 plus 2 sets of mid-trimmer, to prevent the ejection system is not smooth, thus extending the life of the mold.
8．模具牌：模具厂标准模具牌，安装在啤塑时操作员一侧，方便识别模具。
8. mold card: mold factory standard mold plate, installed on the operator side of beer plastic, easy to identify the mold.
9．散气镶件：制品易困气部位，通常加散气镶件，但可根据特殊情况增加散气针或散气钢做的镶件，利于排气，从而提高生产效率。（使用日本PorceraxⅡ PM-35钢）
9. Dispersion insert: The product is easy to trap gas parts, usually with a diffuse insert, but according to special circumstances can be added to the diffuse needle or steel insert, conducive to exhaust gas, thereby improving production efficiency. (using Japanese Porcerax II PM-35 steel)
10．锁模片：为保证吊模及运输时的安全，需在啤塑操作员一侧加锁模片。两板模装在A、B板上，三板模安装到面板上与B板上。
10. locking die: to ensure the safety of the lifting and transportation, the mould locking piece is needed on the side of the beer molding operator. The two die is mounted on the A and B boards, and the three plate die is installed on the panel and on the B board.
